Eotech X320 User Manual Uživatelský manuál

See the Unseen User Manual User Manual

10 2. Operation The X320 Thermal Imaging Camera Rubber Armored construction Submersible to 1 meterFloats in water Standar

Holding the Camera ⇒ The Camera can be mounted to a tripod using the 1/4-20 insert. ⇒ The Camera can be held either right-handed, or left

12 Loading the Batteries Open the battery Door Unscrew Battery Door knob Counterclockwise Open the door to install batteries Install 2 AA Lithium

Batteries ⇒ L-3 EOTech recommends the use of Lithium AA batteries. The camera can operate with Alkaline, Nickel-Metal(NiMh) rechargeable,

14 Camera Start-Up The camera requires approximately 5 seconds of start-up time. During these 1st 5 seconds after the camera is switched on,

L91 Batteries provide enough charge for approximately 6 hours of operation. Operating Time is based on a display set to minimum bright

16 Adjusting the Display Brightness Turn the User Control Switch past the on/off detent, continuing to increase the LCD display brightness. Brig

function for a long push is to cycle through white/black hot and colorized video modes. ⇒ Extended Long Push (Factory Defined) – Press and

18 Cleaning Do not apply any chemicals to the camera. ⇒ Clean the body of the camera using a water-moistened cloth. ⇒ Clean the Lens with

19 When starting the GUI a warning message appears on the computer screen It is recommended that the user insert a fresh set of batteries or plug

2

20 The single panel screen shown above provides access to all of the customization options available to the user via 10 separate user zones. Fi

21 Multi-function Button Settings This zone configures the operation of the User Control Switch. Drop Box Expanded The Very Long Push drop

22 1.00× is always selected and is the default power up setting. Factory defaults select 1.00× and 2.00× and pressing the User Control Switch cycles

23 Below is an example of a standard image with Hot Target Level I and II applied. Standard Image Hot Target Level I Hot Target L

24 Temperature units selected in the Temperature Units zone applies to the temperature setting temperatures used in the custom colorization set

25 assigned to perform Manual Touch-up for improved image quality. Display Icons turns symbology elements ON/OFF in the display. o Temperature

26 DO NOT DISCONNECT THE CAMERA FROM THE COMPUTER OR REMOVE POWER WHILE DATA IS BEING SAVED BY APPLY CHANGES. IF THE CAMERA LOSES POWER WHILE DATA I

You may also return to factory defaults without using the GUI by holding down the User Control Switch for 5 seconds.4. Accessories Contact L-3 EO

28 AC/DC Power Adapter Connect the AC/DC Power Adapter to the X320 Connector labeled “Power”, and to AC power (wall outlet). If batteries are in

29 4. Additional Information Specifications Detector Type Amorphous-Silicon Microbolometer Spectral Response 7 to 14 microns Thermal Performanc

3

30 Physical Size 5 ¼ x 4 ½ x 2 (inches) 13.4 x 11.4 x 5.1 (cm) Weight 13oz. (381g) with batteries Eye Cup Integral to camera Environmental Operatin

31 Frequently Asked Questions Q1 Can different battery types be used? A1 As long as the battery is an AA size, the user can install Al

32 Trouble Shooting Guide Problem Possible Cause Possible Remedy After waiting the 5 seconds of warm up, the video does not appear and/or the scre

33 L-3 EOTech Warranty Product(s) will conform to L-3 EOTech’s current drawings and specifications at the time of delivery and be fr

34 HOW TO RETURN PRODUCTS FOR REPAIR: 1. Do not return product to place of purchase 2. Please complete the Return Authorization Request off the

35 L-3 EOTech/ Infrared Products Division 3414 Hermann Dr Garland TX 75041 5002035-1 Rev D Phone: 1-888-EOTHOLO 1-888- 368- 4656

4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

5 User Manual P/N 5002035-1 Rev D ©2014 L-3 EOTech. All Rights Reserved Patents This product is covered by one or more of the follow

6 1. Introduction ... 7 • Welcome to Infrared ...

7 1. Introduction Thank you for choosing the X320 Thermal Imaging Camera. With its small size, rugged design, and simplicity, you can now focus on

8 The X320 was designed to sense differing amounts of long wavelength infrared coming from the various areas of a scene and to convert the

• Handling and Precautions ⇒ All batteries can cause property damage or bodily injury if a conductive material such as jewelry or keys